A new area for the fogging test within the automobile industry is HID (High Intensity Discharge) headlight components. HID lights operate at high temperatures in a micro-environment typically comprised of a polymer reflector and lense and the glass HID bulb. The outgassed SVOCs re-condense on all surfaces of the bulb, reflector and lens when the HID light is turned off. The resultant film reduces light transmittal from all components and refracts or scatters the light in undesirable directions, potentially reducing night time visibility for the driver.

Methods

Fogging Behavior DIN 75201 Reflectometric method, photometric method, fogging method, gloss method

According to this method, a prepared sample is placed in a beaker that is then covered with a glass plate. The plate’s Reflective Index has been measured and recorded using a handheld reflectometer. For a period of three hours the sample is heated to 100°C, while the glass plate is cooled to 21°C. The heat causes the sample to release SVOC gasses that condense on the cooled glass plate creating a “Fog” (F). The Reflective Index of the fogged glass is measured and recorded.

Fogging value (Fv) is expressed as a percent of change in the 60° Reflective Index of a glass plate that has been fogged in accordance with the procedures (R1) to a clean glass plate (R2).

Fv = (R2 x 100)/R1

Where:

Fv = Fogging value

R1 = the mean initial reflective index of the glass plate with the fogging condensate

R2 = the mean initial reflective index of the glass plate

DIN specifies the maximum value for Fv in this test at 90%

fogging tester with these three test methods

Fogging Behavior DIN 75201 Gravimetric method

According to this method, a prepared sample is placed in a beaker that is then covered with an aluminium foil disk. The disk’s mass has been measured and recorded. For a period of sixteen hours the sample is heated to 100°C, while the aluminium foil disk is cooled to 21°C. The heat causes the sample to release SVOC gasses that condense on the cooled aluminium foil disk creating a “Fog” (F) that has a measurable mass (m). The amount of fogging condensate is determined by weighing the aluminium foil disk again after the test and subtracting the known mass of the same aluminium foil disk before fogging.

mF = m2 – m1

mF = the mass of the fog condensate collected during the test

m1 = the initial mass of the disc of aluminum foil (milligrams)

m2 = the mass of the disc of aluminum foil with the fogging condensate (milligrams)

This is the preferred method because the longer run time and simple measurements increase accuracy while minimizing errors inherent in the reflectometric method such as contaminated or damaged glass, using the incorrect side of the glass, or errors in measuring the reflective index

FT-F1 Fogging Tester is professionally designed for the fogging characteristics evaluation of volatile constituents of decorating materials used in cars and aircrafts, e.g. plastic articles, polyurethane, textiles, leather, adhesives, nonwovens and thermal forming elastomers at high temperature conditions. It also could be used for the fogging phenomenon test of high intensity discharge (HID) headlamps of cars.

Three test methods for inner materials of automotives

• Gloss Method

the specimen is heated in the beaker and its volatile constituents are condensed on the cooling glass plate. The fogging value could be obtained by calculating and comparing the gloss values occurred before and after condensation process.

• Haze Method

the specimen is heated in the beaker and its volatile constituents are condensed on the cooling glass plate. The fogging value of the specimen could be obtained by calculating and comparing the fogging values occurred before and after condensation process.

• Weighing Method

the specimen is heated in the beaker and its volatile constituents are condensed on the cooling aluminum foil. The fogging value – the weight of condensed constituents could be obtained by analyzing the weight changes of aluminum foil occurred before and after condensation process.

To inflate designated pressure compressed air into car light inside and test the amount of gas leak.  Then you could evaluate leakage property of car lighting by results.

Features:

Micro-computer control, LCD display;

Manu interface, PVC operation board;

Positive pressure method;

Adjustable testing range;

Two testing modes: expansion restraining and expansion non-restraining;

Multi-testing methods of burst test, creep test and creep to failure test.

“One key” testing process;

Automatic statistics;

Mini-printer;

RS232 port;

Network transmission interface for LAN data management and Internet data transmission.

Technical Indexes

Test Range: 0~250kPa; 0~36.3 psi (rountine)

0～400kPa;0～58.0psi (optional)

0～600kPa;0～87.0 psi (optional)

0～1.6MPa;0～232.1psi (optional)

Gas Source Pressure: 0.4MPa~0.9MPa (users provide gas sources by themselves)

Power: AC 220V 50Hz

More details please feel free to contact Shirley Wu via:

EMAIL: trade2@labthink.cn

SKYPE: shirley-labthink

MSN: shirleywu_labthink@hotmail.com

Related product:

• Fogging Tester
• Air Permeability Tester

More about Labthink (http://www.labthink.cn/en):

Labthink, focusing on laboratory testing instrument R&D, production and laboratory IT services as the core business, is dedicated to provide perfect and professional product quality control solutions for customers in packaging, food, pharmaceutical, medical, daily chemistry, printing, adhesive, automotive, petrochemistry, bioscience, construction, new energy and other industries.

Customers worldwide(parts):

Labthink, think for you only!

Fogging tester can be used to test the fogging of the xenon lights.

Fogging Tester conforms to standards of ISO 6452, DIN 75201 and SAE J1756 etc.

FEATURES:

1. Fit for laboratory running and low noise

2. Bath temperature control accuracy can reach 0.1 degree Celsius, creating precise testing conditions

3. Easy to operate and safe

4. Worldwide first class components, stable and reliable

5. Human friendly design

Technical data:

1. High Temperature Bath Range: room temperature~150ºC

(optional: room temperature~280ºC)

2. Resolution of High Temperature Bath: ±0.1ºC (150ºC)

3. Low Temperature Bath Range: 0ºC~100ºC

4. Resolution of Low Temperature Bath: ±0.1ºC

For more information, please feel free to leave us message.

Related product:

PARAM^TM TQD-G1 Air Permeability Tester

More about Labthink:

Labthink provides excellent testing equipments and services for Labs, quality and safety control of polymer materials, such as flexible packaging, pharmaceuticals, foodstuff, cosmetics packaging, printing, adhesive, automotive, petroleum chemistry, environment, biology, new energy, construction, astronautics and electronics.

Customers worldwide(parts):